Open the Exposure Settings dialog to adjust the exposure settings of the camera and to optimize it for the current lighting condition. The MOBOTIX camera is equipped with several automatic features so that the best possible images can be created under all weather and lighting conditions. Normally, only extreme conditions call for manual modifications of the exposure settings.
|Linked Image Control||
This mode uses the same exposure values and internal image correction settings for both sensors. This ensures that the images from both sensors look as similar as possible.
Note: This parameter is only available for models with identical image sensors.
The automatic contrast should always be activated in order to create high-contrast images under all lighting conditions.
Changing the Brightness parameter will adjust the entire image area.
This parameter also is used for adjusting the brightness of an image. However, it only affects the darker portions of an image.
Full Image Area: The full image of the sensor (i.e. the 1x Zoom, no lens correction on cameras which have this feature) is used to determine the proper exposure. The following parameters for exposure windows, exposure weighting and white balance weighting are used to set the appearance of the image.
Visible Image Area: This mode optimizes exposure control for the visible image section. Other parameters are not used, i.e. the settings of the exposure windows, exposure weighting and white balance weighting parameters are ignored.
Note: If the camera uses Full Image Recording, this setting could render the recorded images unusable (e.g. when zooming into very dark or very bright areas of the image, the rest of the image will be overexposed or underexposed, respectively).
Exposure windows are defined image areas that are used for exposure and color adjustment. To facilitate exposure window positioning, you can select from a number of pre-defined exposure windows.
Predefined exposure windows:
Using this parameter, you can define how much the exposure windows are to be considered for exposure control—relative to the rest of the image.
The Total setting will use the entire image for exposure control. The factory default setting is 100%, which means that only the exposure windows are used for exposure control.
|White Bal. Weight||
Using this parameter, you can define how much the exposure windows are to be considered for white balancing—relative to the rest of the image.
The factory default setting is Total, which means that the entire image is used for white balance. The setting of 100% means that only the exposure windows are used for exposure control.
Note: The values of 0% .. 90% are not available on some image sensors.
On: Displays the defined exposure window(s) with green frames in the image. Exclusion windows are shown with a red frame.
This parameter of exposure control (default is 40%) specifies the average brightness of the image pixels considered for exposure control (→ exposure windows) that the camera tries to reach; it is thus the target value for the finished image's brightness. In order to reach this value, the camera first tries to change the exposure time within the limits set by the minimum and maximum exposure time and adjusts the hardware amplification within the internally defined limits.
|Minimum Average Brightness||
If the brightness continues to decrease, the camera extends the exposure time and increases the hardware amplification to maintain the specified average brightness, until the maximum exposure time has been reached.
If it still gets darker, the image brightness drops below the value of the average brightness and approaches the value of the minimum average brightness. If the image brightness drops below this value, the camera will activate the software amplification to maintain the minimum average brightness for as longs as possible.
When using this parameter, the following rules apply:
This feature improves the contrast of dark images.
Note: Activating this parameter may result in an increase of image noise.
|Sensor Gain Range||
This parameter sets the range in which the hardware gain is operating. When using this parameter, the following rules apply:
These parameters influence the balance between an exposure time that is as short as possible and hardware amplification that is as low as possible. The objective is to reach a fair compromise between clear images of moving objects (short exposure time, high amplification) and as little image noise as possible (long exposure time, low amplification).
When using the camera in a web application, a positive value would create images with little amplification (i.e. little image noise); moving objects would be displayed in a blurred manner. On the other hand, a security application would require a negative value to show moving objects as clearly as possible, even if this would mean higher image noise.
|Max. Exposure Time||Set the maximum exposure time in seconds.|
|Min. Exposure Time||Set the minimum exposure time in seconds.|
|Frequency of Power Supply||
This parameter sets the camera to the power supply frequency of the respective country to prevent interference by artificial light.
The factory default setting for Europe is 50 Hz. For Canada, the U.S.A. and Japan, set the power supply frequency to 60 Hz. If the camera is used in daylight conditions (rather than artificial illumination), you can also use the No artificial light setting.
Klicken Sie auf Setzen, um die Einstellungen zu aktivieren und bis zum nächsten Neustart der Kamera zu sichern.
Klicken Sie auf Voreinstellung, um diesen Dialog auf die werkseitigen Voreinstellungen zurückzusetzen (dieser Button wird nicht in allen Dialogen angezeigt).
Klicken Sie auf Wiederherstellen, um alle Änderungen seit dem letzten permanenten Speichern der Konfiguration zu verwerfen.
Beenden Sie den Dialog durch Klick auf Schließen. Hierbei wird geprüft, ob Änderungen der Gesamtkonfiguration vorliegen. Ist dies der Fall, werden Sie gefragt, ob die Gesamtkonfiguration dauerhaft gesichert werden soll.